Built for enthusiasts and professionals -
MPVI3 by HP Tuners, the fastest and most sophisticated OBDII interface device to date. Standard with Pro Feature Set (
PROLINK+ cable sold separately).
BIGGER, BETTER, FASTER.
Pro is the new standard with MPVI3. Take advantage of Pro Feature Set capabilities like standalone data logging and
PROLINK+ compatibility (sold separately) already built into your new device. MPVI3 redefines the limits of speed and control with faster standalone data logging and 2X the storage capacity compared to the previous generation. Log more runs (faster) and store more calibrations on your MPVI3, all with the convenience of eliminating your laptop from the equation.
WHAT'S NEW WITH MPVI3?
Standard with Pro Feature Set
2X Storage (from 4GB to 8GB)
Faster Standalone Data Logging
High-Resolution Accelerometer
But don't be fooled, MPVI3 continues the legacy of its predecessor with features like Bluetooth 5.0, an M8 motorsports-grade screw-on connector, RGB LEDs, and USB-C connectivity (4MB/s).
THE ONLY TOOL YOU NEED IN YOUR TOOLBOX.
Get equipped with the most inclusive scanning, logging, and calibration package in the industry.
Connect > MPVI3 is an advanced OBDII interface tool, connecting your vehicle's control modules to our VCM Suite software.
Read > Run complete diagnostics, monitor vehicle performance, read from various vehicle control modules, and more in VCM Suite.
Edit > Optimize your performance, fuel economy, or whatever your vehicle goals may be in VCM Editor with a multitude of defined parameters.
Write > When you are ready, license and tune any vehicle currently supported by HP Tuners with the fastest read and write speeds available.
Drive >>>
From dedicated race cars to tow rigs, off-road machines, next-level street cars, and fuel-efficient daily drivers, HP Tuners delivers the ultimate solution for builds and enthusiasts of any caliber.
VCM SUITE
VCM SCANNER - your feature-rich OBDII scanning & diagnostic software.
View, chart, and log all your diagnostic data in real-time via your vehicle's OBDII diagnostic port-command fans, open/closed loop, gear select, timing, air-fuel ratio, and so much more. Read Diagnostic Trouble Codes (DTCs), experience standalone data logging, and explore a multitude of special functions like Gear/Tire Wizard. Built-in VCM controls are also supported.
VCM EDITOR - your comprehensive vehicle control module calibration software.
Get started by reading your vehicle's different control modules’ flash memory and save it as an .HPT file. Adjust a multitude of parameters, like spark, fuel, RPM limits, fan temps and speeds, transmission shift points and pressures, exhaust valve control, speedometer settings, and so many more. Then, write all your changes back to the vehicle using your MPVI3.
MORE DATA AT YOUR FINGERTIPS WITH PROLINK+
Need to view more data with your MPVI3 from a wideband sensor, boost gauge, or other additional sensors? Get equipped with the
PROLINK+ cable (sold separately), enabling users to wire in and record up to 2x analog signals (from a wideband sensor, map sensor, etc.) and 1x CAN bus signal simultaneously. Now standard with Pro Feature Set, MPVI3 is fully compatible with the
PROLINK+ cable straight from the box.
*
PROLINK+ is not required for MPVI3. The
PROLINK+ cable must be wired in for use.
HP TUNERS' COMPLIANCE STATEMENT
HP Tuners designs and manufactures software and hardware tools for vehicle diagnostics, scanning, logging, calibration, and data acquisition purposes. The authorized use of such tools is to bring a motor vehicle into emissions compliance and/or to maintain emissions compliance, as well as for use on competition/racing and other exempted vehicles. HP Tuners does not create or provide tunes or pre-made calibrations.
HP Tuners' Terms of Use, policies, and agreements mandate that users shall comply with all local, state, and federal laws. In using HP Tuners software and hardware tools, you are representing, warranting, and agreeing not to use, employ or allow any HP Tuners tools to operate as a defeat device or to violate emissions compliance in any manner whatsoever. You further represent warrant and agree that the HP Tuners tools shall only be used by manufacturers, calibration businesses, and professionals to develop emissions-compliant and/or exempted calibrations.
Limited Product Warranties
Interfaces and Hardware Components
Duration: One (1) year from the date of purchase
Coverage: This limited one (1) year warranty only covers product defects caused by HP Tuners and is only redeemable within the original country or region of purchase by the original purchaser. This limited warranty does not extend to software or other digital products. To make a warranty claim, please provide your Proof of Purchase (original invoice and order number), device serial number (if applicable), Debug and Info logs, license file and photo evidence of defects to HP Tuners Support.
The Limited Warranty does not cover:
- Damage to product resulting from accidents, neglect, or misuse; exposure to liquid, moisture, or dirt; abnormal conditions (temperature extremes) or improper storage.
- Scratches or other cosmetic damage.
- Damage to connection points due to excessive force or improper use.
- Devices that have had the serial number removed, defaced, damaged, or altered in any way.
- Ordinary wear and tear.
- Products that have been modified, tampered with, or serviced by an unauthorized party.
Vehicle Control Modules
(PCM/ECM/TCM- New and Modification Service)
Evaluated on a case-by-case basis.
Vehicle Control Modules, whether new or modified by HP Tuners, carry no warranties, expressed or implied, and are offered "as is". In the event of a problem with a Vehicle Control Module product or service, please submit a ticket to HP Tuners
Support for resolution.
